Lifetone HLAC151 Bedside Vibrating Fire Alarm and Clock

Lifetone HLAC151 Bedside Vibrating Fire Alarm and Clock 

Lifetone HLAC151 Quick Start Guide

STEP 1 – POWERING THE HLAC151

• Remove the battery door from the back of your HLAC151.
• Insert four D-cell alkaline batteries as shown in the illustration at right, matching the polarity signs (+ and –) in the open compartment. You should do this before plugging your HLAC151 into a wall outlet.
• Replace the battery door securely. A ashing “TEST” on the screen tells you the batteries are installed correctly.
• Plug the Lifetone HLAC151 into an electrical outlet near your bedside. Don’t use an outlet that is controlled by a wall switch.
• You may plug in the bed shaker now or at any time after setup.
• The word “TEST” continues to ash on the screen. Go to STEP 2.
• NOTE: The HLAC151 operates on AC power. The batteries are only for backup during electrical outages.

STEP 2 – SETUP WITH YOUR SMOKE DETECTOR

• The word “TEST” is fashing on the screen and your HLAC151™ says, “Press the red button to begin.” Press and release the red TEST/SILENCE button on the back.
• “TEST” stops ashing and your HLAC151 says, “Please wait.”
• After about 30 seconds, “TEST” starts ashing again and your HLAC151 says, “At the tone, test your smoke alarm.” This means it’s time to press the test button on your smoke alarm.
• Go to the most distant smoke alarm you want detected. If your alarms are interconnected, use the nearest one instead. Press and hold the test button on the smoke alarm until the Lifetone HL alarm sounds, indicating a successful setup test. Between two and six T3 cycles (groups of 3 beeps) of the smoke alarm will be required. You’ll need to hold the smoke-alarm button down for 10 to 30 seconds.
• If the test is not successful, try again using a nearer smoke alarm. You may try as many times as you like. Your HLAC151 will continue with this test until it is successful.
• When the test is sucessful, the Lifetone HL™ alarm sounds and “ F I R E ” ashes on the screen.
• When the setup test has nished, the“12 hr” option for the time display appears on the screen and your HLAC151 says, “Now, set the clock.” Go to STEP 3.
• If the setup test has not been successful after several tries, the smoke alarm may not be issuing a T3 signal. See the section titled “TESTING THE LIFETONE HL in the Users Manual.

STEP 3 – SETTING THE CLOCK

• On the time display, “12hr” appears. To select 24-hour time, press + or – .
• Press SET CLOCK. The hour will ash. To change the hour, press + or – .
• Press SET CLOCK. The minute will ash. To change the minute, press + or –
• Press SET CLOCK. The year will ash. To change the year, press + or – .
• Press SET CLOCK. The small “M” and “D” will ash. To change to a day-rst display of the date, press + or –.
• Press SET CLOCK. The month will ash. To change the month, press + or –
• Press SET CLOCK. The day of the month will ash. To change the day, press + or – .
• Press SET CLOCK. The “E” (for English) will ash. To change to Spanish (”S”) or French (”F”), press + or – . Press SET CLOCK again.
• The clock will show the day of the week to the right of the date. If you prefer to display the year instead, press SET CLOCK again.

NOTE: When you need to reset the clock, press and hold SET CLOCK until “12hr” appears. Release the button, and then repeat all parts of STEP 3.

STEP 4 – SETTING THE WAKE-UP ALARM

• If the wake-up hour isn’t already ashing, press and hold SET ALARM. Release the button when the wake-up hour ashes. To change the hour, press + or –
• Press SET ALARM. The wake-up minute will ash. To change the minute, press + or –
• Press ON/OFF to enable or disable the wake-up alarm. The bell icon at lower
• You can use the HI LO slide switch to adjust the volume of the wake-up alarm. The emergency alarm always sounds at full volume.

NOTE: To change the wake-up alarm time, press and hold SET ALARM until the wake-up hour ashes. Release the button, and then repeat all parts of STEP 4.

Warranty

2 Year Warranty